Tags

The best way to Care for Cleaning Equipment

As a cleaning company owner, exactly how many times do you walk right into a janitor closet in order to find foul mop pails, dirty equipment, vacuum cleaners which haven’t been emptied, and spray bottles that no longer spray correctly? Have your managers or you taken some time to train your employees on how to properly care for your equipment? Utilize this checklist to help keep your materials and equipment in top working condition.

Plastic Spray Bottles

Wipe bottles as essential to avoid build-up and deposit

When desired replace label

Periodically take apart cause and clean to prevent clogging

Wipe down in and out as needed

Rags

Do not leave lying around – they really are a safety and disorder risk. Keep in a bag for filthy rags

Wipe and disinfect front border as needed

Brushes

Excess, shakes out. If brush is not clean, wash it out in lukewarm cleaning solution and rinse with clear water. Let dry with bristles.

Storage – hang brush – don’t put the brush weight.

Sweepers

When wet, usually do not stand on its straws don’t use. Do not use broom. Therefore it will wear evenly, rotate often.

Putty Knife

After each days use, wipe knife to remove debris and moisture.

Keep in clean, dry area.

Border the blade as needed to keep it sharp

Rinse with water immediately after use.

Don’t use dust mops on floors that are fatty.

Remove loose soil frequently, using a vacuum cleaner if possible shake into waste receptacle that is large.

Never store a mop on the ground. Hang the mop so air can circulate.

Before using a fresh mop, soak for many minutes to remove sizing and toughen the fibers.

Rinse after use.

It could be ruined because the fibers will bust if it is squeezed too hard or twisted.

Cut irregular or loose strands off.

Hang mops to dry in a light, airy area. Never store on the floor or in the mop bucket.

Floor Finish Mops

After using, wash all floor finish or wax with water that is clean out.

Wring out as much water as possible, shake to fluff fibrils.

Never use soap or detergent on a mop designed for floor finish.

Set mop after use in a clean plastic bag.

Pails & Wringers

Do not use force on a wringer lever – use just enough hand pressure on the lever to wring the mop out.

Eliminate any loose mop head yarn, string or foreign matter that becomes tangled in the wringer.

Wash and scrub all surfaces of the pail with disinfectant. Rinse with tepid to warm water and wipe dry. Keep wringer tight and oiled.

Keep wringer in “release” position when it is not being used.

Rinse blade after use in water that is clean.

Wipe dry, usually do not keep with blade down or crouched.

Upright Vacuum Cleaners

Empty tote consistently.

After emptying wipe outside of hoover.

Assess belt when needed and change.

Magnet that is empty bar after every use.

Buffers

Wipe whole surface down after each day’s use. Additionally wipe twine.

Check pad for replacing.

Blow motor approximately every 2 weeks out.

Once per month check bolts and screws to ensure they’re tight.

Slow Speeds

Wipe whole surface down after each day’s use. Also wipe cord.

Rinse tank after each use.

Assess drive unit for cracks on wear.

Artificial Flooring toilet cleaners Pads

Flooring pads may be used on either side. The pad should be set aside for soaking or cleaning once both sides have been used.

Floor pads can be cleaned by rubbing one against the surface of another. Or you can definitely utilize a hand scratcher. Pads that do not react for this method needs to be soaked overnight in a concentration of synthetic detergent or stripping solution. After soaking, each pad must be rinsed under a sharp stream of water that was hot. After a final rinse of cold water, the pads must be shaken and put on a flat, non-rusting surface for drying. Pads usually are not prepared for re-use until they are completely dry.

Suggestion: When pads become excessively worn, they are able to be cut into small sections that may be used as foot or hand scratch pads.

Out in, wipe out and in after each use.

Rinse and wipe fasteners and hoses.

Carpet Machines

Rinse out in of tank, filters, hoses and attachments.

Pump-Up Sprayers

Discharge pressure.

Wipe outside.

When empty, rinse out, spray water through sprayer to help keep from becoming plugged up.